Non-union electrical aptitude tests: IEC, ABC and employer tests
Short answer: non-union electrical apprenticeships, such as those run by IEC (Independent Electrical Contractors) and ABC (Associated Builders and Contractors) chapters, do not use the IBEW/NECA test. Each chapter or employer chooses its own test, and some use none. One publisher, Ramsay Corporation, sells electrical tests for apprentice hiring that add arithmetic, schematic reading, signal flow and electrical principles, with shorter time limits than the union test.
Start by asking the program for the test name. Each test has different sections and timing, and your study plan should follow them.
How do you find out which test a program uses?
Ask the chapter or employer three questions when you apply:
- What is the name of the test, and who publishes it?
- Which sections does it have, and how long is each one?
- Is a calculator allowed, and is there a minimum score?
Programs answer these routinely. If you only get a general description ("math and reading"), prepare for both the union-style algebra and the Ramsay-style sections below, since the overlap is large.
What is on Ramsay's electrical tests?
Ramsay Corporation publishes its test specifications on its product pages. Two of its electrical tests:
| Test | Items | Time | Content |
|---|---|---|---|
| Electrical Aptitude Test, Form BR (online) | 36 | 18 minutes | Mathematics, electrical concepts, electrical schematics, process flow, signal flow, electrical sequences |
| Electrical Apprentice Skills, Form A | 84 | 102 minutes | Reading (24 items, 24 min), arithmetic (20 items, 30 min), pre-schematic reading and signal flow (20 items, 20 min), electrical principles and troubleshooting (20 items, 28 min) |
Form BR gives you about 30 seconds per question, so speed matters far more than on the union test. The Apprentice Skills test is longer and closer in feel to the union test, with two extra electrical sections.
How do signal flow and schematic questions work?
These questions show a diagram of boxes, switches or logic steps and ask what happens at the output. You do not need trade knowledge, only careful tracing. A typical example in words:
Two switches, A and B, are wired in series with a lamp. Switch A is closed and switch B is open. Is the lamp on?
In series, current must pass through both switches. B is open, so the path is broken: the lamp is off. If the switches were in parallel, either closed switch would complete the circuit and the lamp would be on.
Practice by tracing a path with your pencil from the source to the output, and writing the state (on/off, open/closed) at every step. Most errors come from skipping a step in your head.
What electrical principles should you know?
- Ohm's law: V = I × R. With 12 volts across 4 ohms, the current is 3 amps.
- Power: P = V × I. A 120-volt device drawing 5 amps uses 600 watts.
- Series circuits: resistances add, and the same current flows through every part. One open part stops everything.
- Parallel circuits: each branch gets the full voltage, and total resistance is lower than the smallest branch.
- Conductors and insulators: copper and aluminum conduct well; rubber, glass and dry wood do not.
- Protection: a fuse or breaker opens the circuit when current is too high.
How should you prepare for a non-union test?
- Confirm the test name and sections with the program.
- Drill arithmetic by hand: fractions, decimals and percentages. The algebra page covers the harder equation work if your test includes it.
- Practice reading with the methods on the reading page.
- For short timed tests like Form BR, practice in 10-minute bursts and aim for about 30 seconds per question.
- If the test includes mechanical questions, use a guide to mechanical principles.
Build the shared skills first: algebra and reading carry over to every electrical test. The free practice test covers both.
Take the practice testFrequently asked questions
Do IEC and ABC use the IBEW aptitude test?
No. The IBEW test belongs to the Electrical Training Alliance, which serves IBEW and NECA programs. IEC and ABC chapters choose their own screening, which can be a commercial test, a chapter-made test or no test at all. Ask the chapter which one it uses.
What is the Ramsay electrical aptitude test?
Ramsay Corporation sells several electrical tests. Its Electrical Aptitude Test Form BR has 36 multiple-choice items in 18 minutes, covering math, electrical concepts, schematics, process flow, signal flow and sequences. Its Electrical Apprentice Skills Form A has 84 items in four parts over 102 minutes.
Is a non-union electrical aptitude test easier?
Not necessarily. Ramsay's electrical tests add schematics and signal-flow questions that the union test does not have, and the 18-minute Form BR is fast. Different, not easier.
Do I need an aptitude test to become an electrician?
Not always. Some merit-shop programs and employers hire helpers or apprentices without one. Union JATC programs, and many IEC and ABC chapters, do test applicants.
Sources
- Ramsay Corporation, Electrical Aptitude Test, Form BR (online)
- Ramsay Corporation, Electrical Apprentice Skills, Form A
- Electrical Training Alliance, The Application Process (union test, for comparison)